installing metal soffit on gable ends

Color Guide Panel J-Channel Fascia sizes vary Pancake Screw Wood Screw 3 of 14 Soffit Ceiling Overhang - Option 1. To create an angle template hold a piece of J-channel against the slope while transferring the angle to another J-channel with a pencil.

Soffit Install Issue At Top Of Gable End Diy Home Improvement Forum

If you enjoy this type of content be sure to like and subscribe.

. - At the Gable ends extend the sheet 1 beyond the gable fascia unless you are using a Gable Trim in which case the sheet should be flush. MARK AND CUT THE FIRST RAFTER ENDS The ridge end of the rafter and often the eve end will need to be cut to the angle of the roof slope. Lap screws should be placed 12 on center hitting the high seam of roofing corrugation.

Do not place screws 12. Nailing strips may be required. Place a piece of hardi siding on the wall at the right height above the piece below and slide it towards the gable until it touches the gable.

Miter the soffit panels to fit into the H-bar or lineal channel. Overlap the ends a minimum of 6 See illustration 1. Cut a tapered piece of wood so the bottom of the eave is even with the board.

A rafter or speed square will have marks for both of these angles. Areas of underlayment that have torn should be replaced or repaired prior to installation of the metal roof. GABLE END SOFFIT PANELS - Start at the base of the gable end and work up to the peak from each side as far as full panels will fit.

Ad Find The Best Soffit Installation In Your Neighborhood. Now measure the height the siding needs to be until the angle starts. Either bend or clip the bottom tip flush with the bottom of the soffit.

Additional screws should be placed 12 on face staggered from top screws. Place an alignment line along the gable end where the first roof panel will be installed. Cap the bottom of the board and run the soffit up to it.

- An overhang of 1 at the eave is recommended. It may be necessary to cut. Seem fastereasier to tack it up to the ladder first then come along after with the fascia cover.

To turn a corner measure from the channel at the wall corner to the channel at the corner of the fascia board subtract 14-inch for expansion. Install a soffit double-channel lineal or H-bar. 2 Install Soffit Panels either horizontally or vertically tucking them inside the J-Channel.

Allow each consecu-tive course to overlap the previous one 3 inches. Metal soffit is installed in much the same manner. Check roof for squareness by making a 3 line across the eaves.

Com-pleting the 3 x 4 x 5 right angle triangle should place the 4 edge or the 3 edge of the triangle parallel with the gable. Browse Profiles On Houzz. To install vertical metal siding start by applying horizontal furring strips and sheathing to the surface youre working on if its uneven.

Channel nail and install along the entire length of the wall surfaces and up to gable peak on side wall 2. Measure the distance from the bottom of the piece to the gable. Find And Compare Local Soffit Installation For Your Job.

3 Install Fascia Trim over end capping the end of the shingles and going up the fascia and fastening with Wood Screws. Slide panels into channel and secure to under edge of fascia board. First Steps Phase 1 Create Anchor Point.

Next transfer the angle of the template to the. If there are any windows or doors nail j-channel around the edges of those as well. As Gable End Trim Install the J-channel to receive siding at gable ends as shown in the illustration.

To create a clean professional look follow these steps. For installation begin at the eave and roll the underlayment horizontally parallel to the eave. SOFFIT PANELS - gable end - Start installation at the base of the gable end working up to the peak as far as full panels will fit.

Fasten gable trim with ¼ x ⅞ Inch metal to metal lap screws. Install the lowest fascia on the gable end first. Gable End Soffit For the gable end soffit do you install it directly to the ladder of the roof and then slide the fascia cover over it or should you install the j-trim and fascia cover and then slide the soffit pieces in like you would on the eave end.

Remove enough of the fascia lip to cover returns then nail them in place and cut the ends off flush with eave ends. In todays episode I will show you how to install board and batten siding on a gable end. - Measure one panel width in from the gable end and run a chalk line from the eave to the ridge.

Placing the Sill Plates. Slide panels into channel and secure into position using nails in panel grooves as required to under edge of fascia board. The roof on this shed is a 4 in 12 slope which makes it a 18 and one half degree angle on the board ends.

Then install the corner posts that came with your siding and nail j-channel along the top and bottom of the wall.

Gable Roof Soffit And Fascia Youtube